How To: Make a story stick
Kitchen cabinets have multiple pieces that must fit together like a jigsaw puzzle. A story stick will help keep the measurements accurate when transferring them from the installation site to the layout and fabrication shop. Watch and learn how to build this helpful tool. Make a story stick.
How To: Open a supra combination lock box
The supra combination lock box has been one of the most trusted door locks for the past forty years, and is commonly used by real estate agents for protecting their houses. Generally a supra combination lock operates with a four-digit password.
How To: Dial open a combination safe lock
In this video tutorial, viewers learn how to dial open a combination safe lock. Begin by turning the lock 4 times to the left. Then turn the lock 3 times to the right. Now turn the lock 2 times to the left and finish by turning it one more time to the right. Users should hear and feel a click when they finish turning the lock. When locking the safe, turn the lock 4 or more times to the left. to ensure security. This video will benefit those viewers who have a safe lock and would like to learn...
How To: Reset the combination on a Giant Surelock
This video is a short tutorial to assist in setting the combination for a Giant Surelock. In the event that a combination is compromised, it is important to change a lock to prevent from unwanted break-ins or theft. Watch this instructional video and learn how to reset the combination on an Giant Surelock.
How To: Clean cut using a table saw, mitre saw or power saw
This short video tutorial Bob Schmidt will show you how to make clean cuts in wood. The blade rotation of any pretty much dictates the best way to run your material through. To get the cleanest cut possible remember these tips: Whenever you run wood through a Table saw, always make sure that your finished side is up. Do the exact opposite when you are using your Power saw. The finished side of your wood must be at the bottom. When you use a Mitre saw, make sure the finished side of the wood i...
How To: Use a Paslode impulse framing nail gun
The Paslode Framing Gun is operated by a gas cartridge and battery so an air compressor is not needed. The tool also has a large range of nails available for different job requirements from 50mm To 75mm. Watch this video tutorial for a demonstration on how to use a Paslode impulse framing nail gun.
How To: Adjust the miter and bevel angle on a miter saw
In this DIY guide from the folks at eReplacementParts, we learn how to adjust the miter and bevel angle on a miter saw using an adjustable square. For step-by-step instructions, and to learn how to adjust the miter angle and a bevel angle on a miter saw yourself, take a look.
News: Copy a key with a Coke can
Attention cheapskates and locksmith apprentices, this key copying solution is stunningly simple. We've really mulled over this one. As you can read in the comments below, people struggle with executing this successfully. But it can and will work. You just have to modify your key to fit your needs.
How To: Clean a 2 cycle engine carburetor from a Ryobi trimmer
If you own a Ryobi trimmer and wish to perform some regular maintenance work on it, you may want to check out this next video. In the tutorial, you find out how to clean a 2 cycle engine carburetor from the Ryobi trimmer using some simple pieces. It's not too difficult to do and can be really handy when you want to make sure your machine is working at optimal capability. So check out the video above, pay attention, be careful, and enjoy!
How To: Replace the broken power cord on your vacuum cleaner
The vacuum cleaner is the most elaborate piece of cleaning equipment many people have, and they should last a long time. Their power cords, however, are generally not very durable. If yours have gotten worn out or actually broken, it's not too challenging to replace it yourself. This video will show you exactly how to do it on a Hoover WindTunnel vacuum.
How To: Disassemble a Dewalt 36V battery
Here is the safe way to disassemble the Dewalt 36V A123 battery pack -- WITHOUT BLOWING THE BMS (metal covered circuit on top of cells) to use the cells with an electric bike or whatever.
How To: Refill an extended reach camping Bic lighter
This video shows you how to take an extended reach Bic lighter (the kind you would use to light a camping stove, charcoal or something similar) and add more lighter fluid to extend it's life. As long as the spark is still good, you can refill your lighter, and this tutorial shows you how to take apart your extended reach lighter and replace the drained lighter. You will need a flathead screwdriver, and maybe a bit of glue to seal everything back up.
How To: Get past a mortice lock with a drill
This lock can certainly be picked, but what if you don't know how, or you don't have anything on hand that can serve as a good lock pick? That's what this video is here for! It will show you how you can drill out the stump of a mortice lock, allowing you to get past the lock entirely. It is not a difficult procedure, and all you really need is a power drill with the appropriate bits, and maybe a template showing you where to drill.
How To: Measure your home's square footage
If you’re selling your home, you’ll need to know its square footage. Why pay a professional when you can measure it yourself?
How To: Restore and Sharpen Rusted Scissors
Leaving scissors wet or forgetting them outside can cause them to rust. Rusty scissors, if you can even open them, will leave brown marks on everything you attempt to cut through. Attempt is the truth—rust dulls the blades of the scissors making it virtually impossible to cut through any type of material, ranging from paper to fabric. But don't toss the scissors in the trash just yet. You can restore rusted scissors to a usable condition provided they are not completely covered and have rust ...
How To: Keep a portable generator quiet by building an enclosure
Having a portable gas-operated or diesel-operated generator available for your home can be very helpful, but can also be very noisy. If you want to quiet a loud electric generator, take a look at this video to soften that sound on a budget. With a little wood and a few other materials, you can build a fan-cooled 'doghouse' to keep a generator quiet.
How To: Identify hardened steel compared to mild steel
Hardened steel is very durable, but nearly impossible to work with at home. If you are trying to choose a piece of steel and can't tell if it's hardened or not, you're in luck, because this video contains a quick method for doing so. All you do is try to file an indentation in the steel with a file. If that doesn't make a mark, you've probably got hardened steel.
How To: Disassemble the Eames lounge chair
If you own an Eames lounge chair and wish to restore it, give it a nice polish, or just know how to take it apart, this tutorial is for you.
How To: Use and take care of a portable band saw
Using a band saw can be really helpful when you have to cut certain metals nice and neatly. Unlike regular band saws, this tutorial covers how to use and take care of one that is portable. This is especially helpful for this hard to reach areas or projects where it's difficult to remove the metal. So check out this helpful tutorial to find out how to use, take care of, and understand a portable band saw. Enjoy!
How To: Refill a butane lighter
In this Home & Garden video tutorial you will learn how to refill a butane lighter. For this you will need any kind of butane lighter that has an opening for refill and any kind of butane refill can. Shake the butane can properly. Then remove the cap and you will see the nozzle. Now hold the lighter upside down and insert the nozzle in to the refill hole. Now press the can down and hold for about four seconds. Repeat this for three to four times. Then replace the cap on the can and try out yo...
How To: Remove a DeWALT miter saw armature bearing
Removing a miter saw armature bearing on a DeWalt miter saw armature can be a bit tricky if because even if you have a bearing puller, you probably won't have enough space to get it in the armature to be able to get it out. You will get a great tip on how you can use a vise to hold down the armature so you can use both hands to work on getting that bearing out.
How To: Remove and replace a drill press chuck
Like any machine, a drill press chuck is prone to wear and tear and with repetitive usage some parts can become unaligned. If you are going to remove a drill press chuck, keep in mind that also with any machine you work with, you'll want to clean off any gunk that accumulates so you have a properly working machine.
How To: Pop a Car Lock with a Coat Hanger
You've done it, I've done it, almost everyone who owns a car has done it: they've gone an locked themselves out. Well, this good how-to shows how to get back into your older model car with nothing more than a coat hanger. It will requre some trial and error to get it done, but this video is a good primer.
How To: Open a locked bedroom or bathroom door
Getting locked out of a bedroom or bathroom can be a real bummer. Fortunately, these locks are easy to "pick" and get yourself in. This how to shows you clearly what to do to get yourself back inside so you don't feel frustrated all day long. This excellent video takes you step by step through the process. This video talks about 2 different types of locks and the two different types of tools you'll need.
How To: Adjust a Rain Bird 5000 Series Sprinkler spray radius
Check out this video tutorial to see how to adjust a Rain Bird 5000 Series sprinkler spray radius with help from Sean Stefan of Sprinkler Daddy.
How To: Replace the carbon brushes inside a KitchenAid stand mixer at home
Has your KitchenAid stand mixer completely given out and won't even turn anymore? We know this can be extremely frustrating, especially when you're in the middle of mixing a pie filling, but don't just give up and get a new one.
How To: Cut hardened steel with an angle grinder
Hardened steel is a very useful material, but working with it is tough because it is nearly impossible to cut with simple tools. What you really need is an angle grinder, and this video will show you how to use one of the powerful power tools to cut a hardened steel ring.
How To: Cut a bolt and save the threads
In this video tutorial, viewers learn how to cut a bolt and save the threads. The materials required for this task are: a hacksaw, steel bristle brush, bolt cutters, wrench, oil and a filer. Begin by putting some oil onto the threads of the bolt. Then place the saw on the desired groove and cut across through the thread. Now brush it with the steel bristle brush to remove the debris. Finish by removing the excess metal with the filer and unscrew the bolt(s). This video will benefit those view...
How To: Remove a stuck drill chuck
If you have a stuck keyless drill chuck and need help on to repair it, check out this next video tutorial. In it you'll find out what tools you'll need for taking out the drill chuck. It can be a difficult job if you lack the right tools and are not careful. So check out the video tutorial above and good luck!
How To: Install a foot throttle on your lawn tractor
In this tutorial, we learn how to install a foot throttle on your lawn tractor. First, weld the petal onto the base and create your own holder for the rod so it stays in position. You will have to bolt it down so it stays in place and doesn't move. On the other side, put a holder on it so the rod stays in place and doesn't move. There should be a bolt on it so it doesn't move and a clamp that is welded onto the end of it. The, string a thin metal wire to connect onto the end and bolt it onto ...
How To: Decode a combination lock
In this video tutorial, viewers learn how to decode a combination lock. Users will need a feeler gauge strip with a modified tip. Begin by sliding the feeler gauge strip in between the wheel and body of the lock. Then start rotating the wheel. When the wheel has resistance, notch the wheel in the right place. Then rotate the wheel counter clockwise three clicks. Do the same for the rest of the numbers on the lock. This video will benefit those viewers who have a combination lock, and would li...
How To: Replace the switch on a corded DeWalt power drill
If the switch on your DeWalt drill is in need of some serious replacement, don't send it off to the shop for expensive repairs… try doing it yourself. It's easy to remove and install a brand new switch on a corded DeWalt power drill. Watch this video to learn how a professional changes the power switch on a corded DeWalt drill.
How To: Fix a power drill grinding noise and chuck problem
Is your power drill making a funky high pitched noise when you try to use it? Or why your chuck on your drill doesn't spin? You first reaction may be to throw it on the ground in anger, but this could actually be simple fix. Sometimes, the gear switch can get stuck in-between gears, and can be fixed by simply moving the gear switch back and forth on your drill. Try that and see if it fixes your battery operated power drill.
How To: Easily fix a sticking Karcher pressure washer
Using a pressure washer to clean the outside of your home or driveway, is great and easy to use. But what happens when it becomes stuck and there's hardly any pressure? Well you're about to find out. In this next tutorial, you'll see how to fix a sticking Karcher pressure washer easily. It can take you a couple of hours to complete or a matter of minutes. Good luck and enjoy!
How To: Change the oil on a John Deere X320 lawn mower
It's important to know that, like cars, lawn mowers need constant maintenance in order for them to work properly through the years. One of the most shared aspects between cars and lawn mowers is the oil. Knowing how to change the oild is very important and not doing so can lead to a machine that has to work twice as hard and can break easily. So in this tutorial, you'll be finding out how to change the oild on a John Deere X320. It's easy to follow and easy to do. Enjoy!
How To: Replace the starter to an Echo trimmer
Knowing how to pull something apart and how to put it back together is important when owning any kind of mechanical tools. In this tutorial, you'll find out how to replace the starter to an Echo trimmer. This video makes the job much easier for you and will ensure that you have a long lasting machine that will help make your yard perfect. So good luck and enjoy!
How To: Replace a trimmer line
Trimmers, or as some people call them weed-whackers, need one important piece for it to work properly: the trimming line, of course. This helps cut off pieces of unwanted grass or weeds with just one single swipe and is easy to replace. In this tutorial, you'll find out how to replace trimmer line in three different devices easily. So sit back, pay attention, and good luck!
How To: Remove a trimmer clutch from most line/string trimmers
If you need to fix or replace the clutch on your trimmer, you will be able to follow along step by step at the best way to take the trimmer apart so you can get to the clutch. There is a tip provided for removing those tricky clutch drum screws as sometimes you cannot get some parts out as easily as they look.
How To: Replace brushes on a DeWalt DW988 18v cordless drill
Replacing the brushes on a DeWalt DW988 18v cordless drill takes about 5 minutes to do, which could in turn add a longer life to your drill and keep more money in your pocket. Rather than having to replace a whole drill due to wear and tear, you can replace the parts on them easily, especially if you have a hard time parting with your tools.
How To: Use a wasp and dremel to etch concrete
Watch this video from the Concrete Network to learn how to uses wasps and dremels to make designs in concrete.